![atto iscsi initiator command line atto iscsi initiator command line](https://linuxroutes.com/wp-content/uploads/2017/04/setup-linux-iSCSI-target-initiator2.jpg)
- Atto iscsi initiator command line manual#
- Atto iscsi initiator command line professional#
- Atto iscsi initiator command line windows#
Then hit Cancel a couple times to back out without making changes. Use the screenshot below to determine what “Position ID” your iSCSI NICs use. From here select the Microsoft iSCSI Initiator and then pull down the Initiator IP drop down list. Select any target, click Connect and then Advanced. You just need to discover what “position” your network iSCSI cards are in to prepare the script.įirst, log in to the server and from command line run “iscsicpl” to open the control panel.
Atto iscsi initiator command line windows#
It’s easy to use and should work on any flavor of Windows that uses Microsoft’s iSCSI Initiator (2008 Standard, Core, Hyper-V Server R2, Enterprise, Windows 7, etc). Rather than clicking 4,000 times (taking into account a few mistakes) I wrote a script that uses a command that Nate gave me to make a Multipath IO connection with iscsicli.exe. That’s 256 iSCSI connections, and if you use the GUI to make these connections, then you’re talking about doing at least 15 clicks per connection (3840 total) and then try to keep everything straight. At Orion there were 8 hosts with 4 NICs and 8 volumes to connect too. It offers a superior hardware specification and a more accessible management interface, while performance is noticeably better.Adding iSCSI targets can be cumbersome when you have several volumes on the SAN and several network cards in several hosts. The 1550D is only marginally more costly than the Potomac and certainly the extra outlay is worthwhile. This is near the maximum read speeds achievable for this drive and real-world tests confirmed this, as copying the 2.5GB of test data to the drive returned an average of 34MB/sec. We then replaced the tape drive with a Seagate Cheetah Ultra320 SCSI hard disk, where the open-source Iometer reported 75MB/sec raw throughput. Moving over to gigabit Ethernet saw backup and restore speeds improve to 10.5MB/sec and 9.5MB/sec respectively – near to native speeds for the Sony tape drive. We saw backup speeds of 7MB/sec, while restoring the data returned average speeds of 8.6MB/sec. Using Windows Backup, our first test over Fast Ethernet was to secure and restore a 2.5GB mix of data. The system immediately identified the new tape drive, leaving us to load the relevant drivers.
![atto iscsi initiator command line atto iscsi initiator command line](https://i5.walmartimages.com/asr/9c6c0d4d-59aa-4d94-b574-6519a8508f5d.fb1f7679a897d08b35fb0238c87a6857.jpeg)
Atto iscsi initiator command line professional#
Using Microsoft’s iSCSI initiator 1.06 on a Windows XP Professional system, we had no problems logging into the bridge as a target. Along with gigabit Ethernet, we ran tests over a Fast Ethernet network to get a feel for performance where the network itself may be a limiting factor. iSCSI aliases, port numbers and CHAP authentication may be modified and the CLI can be accessed, although this feature did contain a scripting bug.įor testing, we first introduced a Sony StorStation AIT260e tape drive to the 1550D, where it was identified correctly and mapped to a LUN ready for use.
Atto iscsi initiator command line manual#
Devices are automatically mapped to LUNs (logical unit numbers), but you can drag and drop them for manual assignments if required. The latter provides easy access to configuration of Ethernet: SCSI, iSCSI and access control parameters. After assigning an IP address, you can use the Command Line Interface or go straight to web browser management. A handy tool when configuring multiple bridge devices is an option to remotely flash the activity LED on the selected unit.
![atto iscsi initiator command line atto iscsi initiator command line](https://image.slidesharecdn.com/usingiscsilfnw-190423170802/95/using-iscsi-lfnw-36-638.jpg)
ATTO provides its QuickNAV utility, which scans the network and automatically discovers the bridge. Installation is simple: you just connect the bridge to the network, add your SCSI devices and power up. It’s also well built inside and out, and ATTO has fitted a small fan inside the top cover to improve internal cooling. Although not as small as the Bridgeworks Potomac (see below), the 1550D is nevertheless a compact device. This month, we take a look at two contenders, with ATTO’s iPBridge 1550D coming under the spotlight first.